
Cavity wall Insulation: survey first, fill second
Not every cavity should be filled. The short answer first, then the Engineer's working.
- Do I have cavity walls?
- Should every cavity be filled?
- How is it done, and what does it cost?
- What should I ask before I sign?
Sources checked 18 November 2026. Listed at the bottom of the page.
Do I have cavity walls?
The Energy Saving Trust's checks: houses built after the 1920s probably have cavity walls, two layers of masonry with a gap between. Houses from before 1920 are more likely to have solid walls.
The brick pattern. A cavity wall usually shows an even pattern with every brick laid lengthways. A solid wall shows an alternating pattern, with the ends of some bricks visible.
The thickness. Measure the wall at an open door or window, from the inside to the outside. A brick wall between 260mm and 350mm thick is likely to be a cavity wall. Narrower than that, it is probably solid. Stone walls tend to be solid whatever their depth.
If the walls are covered with render or cladding, the Trust says to ask a building professional. Some older houses do have a cavity, but one too narrow to insulate, and those walls are treated as solid.
Houses built from the 1990s onwards generally have wall Insulation already. Your EPC may show whether a cavity is insulated.
Why it matters: the Trust says about a third of the heat lost from an uninsulated home escapes through the walls.
Should every cavity be filled?
The Energy Saving Trust says a home suits standard cavity wall Insulation if:
1. the outside walls are unfilled cavity walls;
2. the cavity is at least 50mm wide and clear of rubble;
3. the masonry or brickwork is in good condition;
4. the walls are not exposed to driving rain;
5. the house is not at risk of flooding.
The Trust also says it might not be suitable for a home that is exposed to extreme weather or flooding, is in poor condition, is at risk of its rooms overheating, or has narrow cavities of less than 50mm, usually in homes built before the 1920s.
Repairs come first. Damaged brickwork or pointing, roofs, gutters and downpipes are put right before any wall Insulation goes in. If they are not, the Trust says you might trap damp or the Insulation may fail. Damp patches on the inside walls are sorted first too.
Steel-frame, timber-framed and pre-fabricated concrete buildings are a different kind of wall: ask a specialist installer or a building professional. In a flat, everyone in the block has to agree, because the whole block is insulated together.
The Trust says the installer must survey the house before any work starts. To see whether a cavity is empty or already filled, a registered installer can do a borescope inspection through a small hole drilled in the outside wall. An Engineer never fills a cavity without surveying it first.
How is it done, and what does it cost?
The Energy Saving Trust describes the job: holes of around 22mm, around a metre apart; the Insulation, usually polystyrene beads, blown into the cavity; the holes sealed with cement. About two hours for an average home with walls that are easy to reach. It is not a DIY job: you need a registered installer.
The Trust's typical cost is around £2,200 in Great Britain and around £1,000 in Northern Ireland, depending on the size of the home. It says the cost is likely to be made back in five years or less.
The UK Government's home Energy guide gives around £1,000 to £3,000 to install, a saving of around £140 a year, and a life of around 40 years. That is for a typical gas-heated semi-detached house, at the October 2025 price cap.
The Engineer's working: £2,200 at £140 a year is nearly sixteen years, not five. The two official sources do not sit neatly together, which is the point. Ask for the cost and the saving for your house, in writing.
What should I ask before I sign?
The guarantee. The Energy Saving Trust says the installation should be guaranteed for 25 years by CIGA, the Cavity Insulation Guarantee Agency, or by an independent insurance-backed guarantee.
The installer. The Trust points to TrustMark, the government-endorsed quality scheme, to find a certified installer, and says to check that they are signed up to a code of professional practice.
The vents. A good installer does not block or seal airbricks, underfloor grilles, wall vents or the trickle vents in your windows. See what to leave alone.
If damp shows up afterwards, go to the installer first. If they won't help or no longer exist, the Trust says to check your paperwork for a CIGA guarantee certificate, or an independent insurance-backed guarantee.
More plain-English guides
Written by an Engineer with 40+ years on safety-critical systems. Free to read, sources checked and dated.
Sources
Energy Saving Trust, "Cavity wall insulation" (last updated 8 May 2026): telling cavity from solid, suitability, how it is installed, typical cost, guarantees and ventilation — energysavingtrust.org.uk
UK Government, home Energy campaign guide, "Insulation" (page last modified 5 November 2025): typical cost, saving and life, for a gas-heated semi-detached house at the October 2025 price cap — cleanenergy.campaign.gov.uk · checked 18 November 2026
General information only. It isn't a Survey of your walls and doesn't replace one.